Minimal single-board computer based on Motorola 68000

栏目: IT技术 · 发布时间: 4年前

内容简介:A minimal single-board computer based on the venerableThis might be capable of running uClinux, but I haven't tried it!

68k nano

A minimal single-board computer based on the venerable "Texas Cockroach" Motorola 68000 16/32-bit microprocessor.

Minimal single-board computer based on Motorola 68000

Features

  • 68HC000 processor running at 12MHz
  • 1MB RAM
  • 64KB ROM
  • 16550 UART providing a 5V FTDI serial port
  • 44-pin IDE connector for CompactFlash card adapter
  • Connector for SparkFun DS3234 real-time clock
  • Only two 74HC glue logic chips required

This might be capable of running uClinux, but I haven't tried it!

Hardware

The 68k nano hardware is simple and straightforward. It can be built on a breadboard (though there may be stability issues at higher clock speeds).

Memory map

Due to the minimal address decoding circuitry, accessing certain memory regions will cause multiple devices to be selected. This should be avoided.

$000000-0xFFFF     ROM (repeats 16 times)
$100000-1FFFFF  X  Forbidden (multiple devices selected)
$200000-2FFFFF     ROM (mirror of $000000-0FFFFF)
$300000-$7FFFF  X  Forbidden (multiple devices selected)
$800000-8FFFFF     Open bus (available for expansion)
$900000-9xxxxF     CompactFlash card
$A00000-AxxxxF     UART
$B00000-BFFFFF  X  Forbidden (multiple devices selected)
$C00000-CFFFFF     RAM
$D00000-DFFFFF  X  Forbidden (multiple devices selected)
$E00000-EFFFFF     RAM (mirror of $C00000-CFFFFF)
$F00000-FFFFFF  X  Forbidden (multiple devices selected)

This is summarized with the following equations:

/ROMSEL  = /A23
/RAMSEL  =  A22
/UARTSEL =  A23 * /A22 * A21
/CARDSEL =  A20

I/O

The 16550's modem control lines are used as a bit-banged SPI interface. A 7-pin header is provided for SparkFun's "DeadOn" DS3234 real-time clock board . Access to SPI is therefore achieved via the 16550's Modem Control Register and Line Status Register.

A 2mm pitch 44-pin IDE connector is provided for storage devices. This is intended for CompactFlash card adapters (operating in 16-bit True IDE mode) but may also work with parallel ATA hard disks. (not tested)

Interrupts

All interrupt sources are routed through the 16550. All 16550 interrupts invoke the level 1 autovector (vector offset $064 ) and it is up to the software to determine the source of the interrupt.

Building it

bom.txt contains a bill of materials. As of this writing (July 2020), all components are available from major distributors like Mouser and Jameco . If purchasing 68000s from eBay, note that vintage ICs are a common target of counterfeiters . For this project I used Toshiba TMP68HC000P-12 chips from Jameco and they work just fine.

All parts are through-hole for that extra vintage feel. Note that some of the decoupling capacitors (C4, C5, C6, C8, and C10) are underneath ICs, so open-frame IC sockets are required. Large IC sockets can also be expensive ( especially DIP-64 sockets!) so a cheaper alternative is to use breakaway SIP 0.1" machine-pin headers .

Due to the spacing of the chips, Textool ZIF sockets won't fit. For the ROMs U5 and U7, Aries 28-526-10 low-profile ZIF sockets will fit, but barely . The release latch may scrape against the RAM IC to its north, but I've found that it's not a huge deal.

You can use either a full-can or half-can oscillator for X1. Note that if using an oscillator with a frequency other than 12 MHz, you'll have to update the F_CPU value in the Makefile. (see below) Also note that, if using a 68HC000, the minimum clock frequency is 4 MHz.

The 44-pin IDE header accepts a CompactFlash adapter board such as this one , available from Amazon and other vendors.

Software

This project uses the vasm assembler and a standard Makefile. Python 3 and PySerial are also required to upload programs to the computer via the serial port. The Makefile also contains rules for burning ROM images to AT28C256 EEPROMs using minipro if you have a TL866II+ programmer. (If you don't have a chip programmer, you should get a TL866II+, they are reasonably priced and available from a number of vendors.)

Building it

Running make rom will build the ROM image and split it into "odd" and "even" halves, rom-l.bin and rom-u.bin . Each file should be 32,768 bytes exactly. Running make burnrom will write these files to a pair of AT28C256 EEPROMs using minipro.

Note:if using an oscillator with a frequency other than 12 MHz, change the value of F_CPU appropriately in the Makefile.

The BAUD variable in the Makefile sets the baud rate of the serial interface. Use the included script baudrate.py to determine which baud rates are usable with a given oscillator frequency.

ROM features

The ROM is fairly minimal--it's closer to a bootloader than an operating system. It supports loading programs from the root directory of a FAT16-formatted CompactFlash card and some basic debugging functionality. It also provides a small set of system calls for I/O to simplify application programs.

The power-up process is as follows:

  • Initialize serial port to 57600 baud, 8 data bits, no parity, 1 stop bit.
  • Test RAM. If a RAM failure occurs, the failed address is written to the serial port and the Status LED flashes rapidly. (This is prone to failure when running on a breadboard at higher clock speeds.)
  • Check for the real-time clock module. If found, print the current date and time to the serial port.
  • Check for a CompactFlash card, and attempt to mount the first partition if it is FAT16-formatted.
  • If the "ENTER" pushbutton is NOT held down:
    STARTUP.BIN
    STARTUP.BIN
    
  • If the "ENTER" pushbutton is held down, enter the interactive command shell and bypass execution of STARTUP.BIN .

Example startup sequence (without STARTUP.BIN ):

68K NANO - ROM VERSION 00009900 (20200708)
(C) 2020 MATT SARNOFF (MSARNOFF.ORG)
TESTING RAM...PASSED

RAM: 1,048,576 BYTES
ROM: 65,536 BYTES
CPU: 12,000,000 HZ
TIME IS 2020-07-07 19:14:36
CARD DETECTED: 250,608 KB 'NO NAME    '
CANNOT LOAD STARTUP.BIN - FILE NOT FOUND

TYPE ? [ENTER] FOR HELP.
>

Command shell

If STARTUP.BIN was not loaded, an interactive command shell is available via the serial port. (57600 baud, 8 data bits, no parity, 1 stop bit). Type ? and press Enter for a list of supported commands. They are summarized briefly here. Note that commands and filenames are case-insensitive .

  • .L - list files in the root directory of the CompactFlash card. Long filenames and hidden files are not displayed.
  • .I - print low-level information about the filesystem on the CompactFlash card.
  • .P file - print the contents of the file named file in the root directory of the CompactFlash card as ASCII text.
  • .H file - print the contenxt of the file named file in the root directory of the CompactFlash card as a hexdump.
  • .T - print the current date and time as reported by the real-time clock module.
  • .T YYYYMMDDWWhhmmss - set the current date and time. The new date/time should be expressed as a string of 16 decimal digits with no separators. WW should be a 2-digit weekday between 01 and 07 inclusive. You can obtain the current date/time in this format with the Unix command date "+%Y%m%d0%u%H%M%S" .
  • .D - enter the debugger.
  • file - any other command is interpreted as a filename to be loaded from the root directory of the CompactFlash card and executed. Unlike MS-DOS, the file extension is required. e.g. to execute the file named foo.bin , enter FOO.BIN . ( FOO will attempt to load a file named foo with no extension).

Serial loader

A break condition on the serial input line enters the serial loader, allowing programs to be uploaded to RAM from a host computer. The Python script serload.py and the Makefile rules make load and make run take care of this.

Debugging

A hardware exception causes a transfer into a basic debugger. The Status LED flashes rapidly and a register dump is printed to the serial port:

*ILLEGAL INSTRUCTION
D0=00000064  D1=0000000A  D2=00000038  D3=00000009
D4=00000000  D5=00000000  D6=00000000  D7=00000000
A0=00E0003C  A1=00001D40  A2=00000000  A3=00F00000
A4=00000000  A5=00000000  A6=000001E2  A7=00EFFFFA
SR=-S0--Z--  PC=00001D3A              USP=7F7EFFDF

[A]BORT/[C]ONTINUE/[S]TEP?

Supported commands are:

a
c
s

TRAP #15 is treated as a breakpoint instruction that also enters the debugger.

API

See API.md for a detailed description of the system calls provided by the ROM API and guidelines for application programs.

Known issues and shortcomings

  • ROM is always present at the bottom of the address space, so the exception vectors cannot be overridden by application code.
  • Interrupt handling is a hack, since all interrupt sources go through the 16550.
  • Address decoding leaves little room for expansion.
  • System calls should set the condition codes to simplify application code.

Future directions

This is a small-scale project. I'm thinking about desiging a larger 68000 board in the future, so I probably won't continue working on this one. Here are some project ideas that I won't have time to tackle, but you're welcome to:

  • Running an existing 68k monitor like TUTOR or zBug .
  • Running a language like EhBASIC or a Forth.
  • Adding FAT16 write support.
  • Booting uClinux like Steve Chamberlin did with 68 Katy .
  • Using the DS3234 real-time clock's SQW output to generate a periodic interrupt. (likely necessary for uClinux)

About

Open hardware, released under the terms of the 3-clause BSD license.

Copyright 2020 Matt Sarnoff.

http://twitter.com/txsector

http://msarnoff.org


以上就是本文的全部内容,希望本文的内容对大家的学习或者工作能带来一定的帮助,也希望大家多多支持 码农网

查看所有标签

猜你喜欢:

本站部分资源来源于网络,本站转载出于传递更多信息之目的,版权归原作者或者来源机构所有,如转载稿涉及版权问题,请联系我们

法律程序的意义:对中国法制建设的另一种思考

法律程序的意义:对中国法制建设的另一种思考

季卫东 / 中国法制出版社 / 2005-1 / 10.0

《法律程序的意义:对中国法制建设的另一种思考》内容为现代程序的概念与特征、现代程序的结构与功能、程序与现代社会、中国法律程序的缺陷、程序建设的程序等。一起来看看 《法律程序的意义:对中国法制建设的另一种思考》 这本书的介绍吧!

XML、JSON 在线转换
XML、JSON 在线转换

在线XML、JSON转换工具

html转js在线工具
html转js在线工具

html转js在线工具

RGB HSV 转换
RGB HSV 转换

RGB HSV 互转工具