内容简介:Sixty/5o2is a minimal bootloader / micro kernel / mini operating system (if you like) forBen Eaters 6502 breadboard computer is a very special kind of animal and brought lots of fun and joy into my last weeks. A 45 years old processor design that is still
Introduction
Sixty/5o2is a minimal bootloader / micro kernel / mini operating system (if you like) for Ben Eaters 6502 Computer on a breadboard. It is only 1.5kB in size (assembled) but comes with quite a nice list of features:
- Load externally assembled programs into RAM via serial connection to Arduino
- Run programs that were previously loaded into RAM
- Load & Run programs in one go
- Debug the full address space via an integrated hex monitor (currently read only)
- Clean RAM for use with non-volatile RAM or during development
- Drive the LCD display even at a clock rate of 1MHz flawlessly
- Drive the mini keyboard for input
- Video RAM based output routines for convenient text display single page / multipage w/ offset
- Interrupt based loading routine to fetch data via the Arduino's serial connection
- Serial Sender (node.js) allowes to upload programs to the 6502 (error mitigation included)
- Fully documented source code
Motivation
Ben Eaters 6502 breadboard computer is a very special kind of animal and brought lots of fun and joy into my last weeks. A 45 years old processor design that is still able to get things done was fascinating enough for me, to give this project a go - especially, since my first machine was a Commodore C64 which I programmed in Basic at the end of the 80'ies and never had the chance to get in touch with 6502 assembly.
On my journey during the last weeks I soon surpassed the current state of development (thanks to Ben's schematics) and was able to write a few programs which I ended up burning onto the ROM using the programmer. Soon enough this became painful, because every codechange required to extract the ROM chip from the breadboard, put it into the programmer, burn it, put it back onto the board. This became time consuming and constraining pretty quickly, especially when I attempted to write slightly more complex programs.
So early on I tested, whether I could use the Arduino, connect 8 of it's digital output pins to the VIA 6522 and transfer key strokes on my Mac serially and render them onto the LCD display. As soon as this worked, the path was clear:
I needed a bootloader that could leverage this power to load externally assembled object code / programs into the RAM and run it from there.
Luckily I was able to speed up the 6502's clock by just replacing the capacitor of the unstable 555 timer circuit by a smaller one such, that loading data serially was - lets say - at least stable enough. That paved the way to more complex subroutines which now make up my "Sixty/5o2" micro bootloader / micro kernel. It works very well with full clock speed of 1MHz and is hopefully helpful to other 6502 enthusiasts as well.
Especially the serial data transfer is enormously stable, since error mitigration (not correction) is baked into a minimalistic protocol, where there the sender side is implemented in node.js. Unfortunately I was not able to get a stable serial connection with serial terminals like screen
, minicom
or picocom
. Hence I decided to build something myself. On the positive side of things I had the opportunity to integrate content transform using base64 encoding as well as simple error mitigation via a checksum algorithm plus a "send packet again" function.
It's not perfect, in places not even nice. Last time I personally touched assembler was 20+ years ago, so please be gentle with criticism. PR's are king.
Hardware Requirements
There are only two requirements, both of them can be mitigated though:
- Use the 1MHz clock (you MUST disconnect the clock module, otherwise it interferes)
- The keyboard buttons are tied low in normal state, when pushed they get tied high (this is opposite to Ben's design in his schematics)
Possible Mitigation Strategies
-
If you want to run at other clock speeds, you MUST adjust a global constant called
WAIT_C
in the bootloader code. It's a multiplier which is used to sleep and just burns a number of cycles in a routine calledLIB__sleep
. If you run at lower clock speeds, adjustWAIT_C
to a smaller number unless keyboard and main menu become usable. -
Should your keyboard be built in a way so the buttons are normally tied high and when pressed turn low , then you need to adjust the routine
VIA__read_keyboard_input
and XORA
with$ff
after it was AND'ed with#$0f
. This way the keystrokes will be interpreted correctly again.
Software Requirements
The following software components are must have's:
- Arduino IDE to be found here
- Minipro or XG GUI software for Windows for thr TL866 programmer available here
- The infamous and awesome VASM Assembler to build for the 6502 (Ben's instructions to build and use to be found here )
- Node.js 8+ to be able to use the serial program loading functionality via the Arduino
- npm or yarn (typically come with node.js) to install the senders dependencies
Installation
The project comes with a number of files, whose functionality is the following:
-
bootloader.asm
- the bootloader / micro kernel / mini os you wanna put into your ROM after assembly -
Receiver.ino
- Arduino source which turns the Arduino into a serial receiver / parallel converter -
Sender.js
- Node.js tool to read 6502 object code / programs and upload them to the 6502 via serial connection -
.sender_config.json
- config file forSender.js
(update your /dev/cu.whateverhere) -
package.json
- package dependencies forSender.js
-
/examples
- some example programs you can load into the RAM
1. Bootloader
Assemble the bootloader:
vasm -Fbin -dotdir -o bootloader.out bootloader.asm
Burn it onto the EEPROM using your TL866 programmer in conjunction with minipro (Linux, Mac) or the respective Windows GUI tool provided by XG (see above).
At this point you can install your ROM chip onto the board and celebrate. You will not remove it from it's breadboardy socket for a while. If your 1MHz clock, RAM, keyboard and LCD are assembled already, you can switch on your 6502 computer and enjoy the main menu of Sixty/5o2 . If the assembly is not done yet, go read Ben's schematics and finish your hardware build.
2. Receiver (Arduino)
- Load
Receiver.ino
into your Arduino IDE. - Open the IDE's package library and search and install the
Base64
package by Arturo Guadalupi v0.0.1 also to be found here - Compile the source
- Upload the program to your Arduino
3. Sender (node.js)
- Install the necessary npm packages via:
npm install
or
yarn
- Adjust the
tty
setting in.sender_config.json
to match the device file which represents your connected Arduino - DO NOT adjust any other value in there, as it will render the serial link unstable (more on that later)
Usage
Arduino Port Setup
Before you can upload a program to the 6502 through the Arduino, you need to setup additional jumper wires between the Arduino and the VIA 6522 AS WELL as the 6502 processor.
GND
Table 1: Port Setup VIA 6522
Arduino | VIA 6522 |
---|---|
31 | 17 |
33 | 16 |
35 | 15 |
37 | 14 |
39 | 13 |
41 | 12 |
43 | 11 |
45 | 10 |
If unsure, look up the pin setup of the VIA in the official documentation .
Table 2: Port Setup 6502
Arduino | 6522 |
---|---|
53 | 4 (IRQB) |
The pin setup of the 6502 can be found here .
Important:Make sure, you still have the IRQB pin (PIN 4) of the 6502 tied high via a 1k Ohm resistor as per the design. The jumper cable to pin 53 of the Arduino just pulls the pin low in short pulses. The line needs to be normal high .
Note:Just one additional wire from the Arduinos power source to the 6502 board will free you of the need of any external power source. Just power your beast via USB and get rid of the power cord.
Uploading a Program
You can now write a program in 6502 assembly language like for example the /examples/hello_world.asm
and assemble it like so:
vasm -Fbin -dotdir -o /examples/hello_world.out /examples/hello_world.asm
Important:Since your programs now target RAM instead of ROM your program needs to have a different entry vector specified:
.org $0200
More on why $0200 later on.
To upload and run your gem onto your 6502, first start up the machine, and reset it. Using the keyboard navigate to Load
using the UP and DOWN keys in the main menu. To start the uploading process hit the RIGHT key which acts as Enter
in most cases.
Now you can upload your program using the Sender.js CLI tool like so:
node Sender.js /examples/hello_world.out
The upload process will inform you, when it's done. The 6502 automatically switches back into the main menu after the upload finished.
Should you encounter any errors during upload, check the tty
setting in .sender_config.json
and adjust it to your Arduinos device port. In addition you can lower the transfer speed to values to 4800, 2400 or 1200 baud. Don't use values above 9600 baud, they won't work.
Navigate to the menu entry Run
and hit the RIGHT key to run your program.
Go celebrate!You're just running your first uploaded program directly from RAM.
Note:You can also use Load & Run
to streamline the process during debugging.
Also note:Resetting your 6502 DOES NOT erase the RAM. So you can reset any time, and still Run
your program afterwards.
And note:The Sender.js
accepts two commandline parameters. If you want, you can also specify your Arduino port manually, whithout having to hardwire it in the .sender_config.json
like so:
node Sender.js /examples/hello_world.out /dev/path_to_arduino_port
Using the Monitor
The hex monitor is very useful during development and debugging. It lets you inspect the whole address space, RAM and ROM. you can navigate using the UP and DOWN keys. The RIGHT key performs a bigger jump in time and space and the LEFT key returns you to the main menu. The monitor is currently read only and the keyboard debouncing is far from being good. But it works.
Important to know - Allocated Ressources
1. $0200
I choose $0200 as entry vector for user land programs. Why you ask? Two reasons:
$0000 up to $00ff $0100 up to $01ff
Therefore RAM is usable in a meaningful fashion from $0200 upwards only.
Note:Due to Ben's (IMO clever) design choice RAM ends already at $3fff, which leaves you with close to 16kByte of RAM for your programs. Should you hit that wall, there's always the option to outsource routines as "standard library", put them onto the ROM and link them from your programs via the VASM linker.
2. Used Zero Page Locations
The bootloader needs to use some Zero Page locations: $00 - $03
. Expect trouble if you overwrite / use them from within your own programs.
3. Used RAM
The bootloader also occupies some RAM. Most part is used as VideoRam to talk to the LCD (consult the source). [In contrast to C64 design there is no interrupt driven scanline routine that updates the LCD automatically from the VideoRam contents yet. A feature to come.] Another few RAM cells are used by the bootloader itself.
However, don't use RAM from $3fda upto $3fff
. Expect problems if you do so.
4. Interrupt Service Routine - ISR
The Interrupt Service Routine (ISR) implemented at the end of available ROM realizes the serial loading. The way it works is quite simple. As soon as the Arduino set up all 8 bit of a byte at the data ports, it pulls the interrupt pin of the 6502 low for 30 microseconds. This triggers the 6502 to halt the current program, put all registers onto the stack and execute any routine who's starting address can be found in the Interrupt Vector Address ( $fffe-$ffff
) - the ISR. This routine reads the byte, writes it into the RAM, increases the address pointer for the next byte to come and informs the main program that data is still flowing. Consult the source for further details, it's quite straight forward.
Shortcomings
- The loader is slow. Quite slow. Even though 9600 baud as choosen transfer speed is not too bad, there are some significant idle timeouts implemented, to make the data transfer work reliably. You'll find it in
Receiver.ino
, theSender.js
does not have any timeouts left other than the necessary but unproblematic connection timeout once at the beginning. The worst is the timeout which allows to reliably read the UART buffer of the Arduino. When reduced, the whole data transfer becomes unreliable. Happy to accept PR's with improvement here. On the other hands, it's not that we transfer Gigabytes of data here ... not even Megabytes, so the current speed might suffice.
Known Problems
Despite the fact that the bootloader and all of it's components are quite stable, there are some problems, which are to be found via a #TODO in the source.
Worth mentioning are the following:
BOOTLOADER__program_ram
Future Plans
- make Hex Monitor read / write
- integrate Arduino Nano directly onto the board to replace all jumper wiring and power the board via USB
- develop a standard library with useful functionality in ROM
- (potentially) integrate a light color / bitmap display like for example the Adafruit 0.96" 160x80 Color TFT Display
- implement a 3d engine using vector rotation and scalar multiplication (or quaternions)
Pull Requests
If you would like to see any particular feature I might be able to provide it ... some day. Unfortunately my spare time is very limited, so you rather develop it yourself. I am happy to screen, test and merge any valuable PR.
Support
Should you be able / interested to support my work and help me spending more time in projects like these or others, your donation is more than welcome:
https://www.paypal.me/janroesnerberlin
Credits
- Ben Eater
- Steven Wozniak
- Anke L.
以上就是本文的全部内容,希望对大家的学习有所帮助,也希望大家多多支持 码农网
猜你喜欢:本站部分资源来源于网络,本站转载出于传递更多信息之目的,版权归原作者或者来源机构所有,如转载稿涉及版权问题,请联系我们。